3M™ 5301 5300 Splice Kit, 0 to 1000 VAC, 10 to 4 AWG Conductor, 3.4 in L Splice, EPDM Rubber
Part #MM5301
$33.87 / Each
Pack: 1/KIT
3M™ motor lead pigtail splicing kits 5300 series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of pigtail (stub) connections at 1000 V and less. The splice's main component, the slip-on lug cover, is made from EPDM rubber. Mastic strips are used for the moisture seal. These kits are designed to be used with copper compression, 1-hole lugs. After being crimped onto the cables, the lugs are bolted together in a pigtail configuration, then insulated and sealed with the 3M™ motor lead splicing kit. Each kit makes three splices and contains the necessary materials (except lugs) needed to make three splices. The lugs must be purchased separately. 3M™ Scotchlok™ copper compression lugs 30000 series or other UL listed copper lugs can be used.
Item Features
- Fast and simple installation
- No torches or heat source required
- No special tools required to install splice
- Thick walls to resist puncture and abrasion damage
- High dielectric constant stress control included with 5/8 kV kits for shielded feeder cables for minimizing size and electrical stress
- Easy re-entry, can be used on cables with a rated operating temperature of 90 deg c and an emergency overload rating of 130 deg C, to splice (insulate and seal) motor lead connections for 1000 vac and less cables sized 16 AWG to 500 kcmil
- Suitable for use with 30000 series copper compression lugs or other UL listed copper lugs
- 365 V/mil dielectric strength
- 750% elongation
- 1400 psi tensile strength
- 1/2 in maximum bolt length
- Polyethylene cable
- 10 to 4 AWG feeder cable, 12 to 4 AWG motor lead conductor size
- Designed to use with copper compression, one hole lugs
- Slip-on lug cover is made of durable EPDM rubber
Description
3M™ motor lead pigtail splicing kits 5300 series are designed for splicing motor lead cables to incoming feeder cables, including the accommodation of pigtail (stub) connections at 1000 V and less. The splice's main component, the slip-on lug cover, is made from EPDM rubber. Mastic strips are used for the moisture seal. These kits are designed to be used with copper compression, 1-hole lugs. After being crimped onto the cables, the lugs are bolted together in a pigtail configuration, then insulated and sealed with the 3M™ motor lead splicing kit. Each kit makes three splices and contains the necessary materials (except lugs) needed to make three splices. The lugs must be purchased separately. 3M™ Scotchlok™ copper compression lugs 30000 series or other UL listed copper lugs can be used.
Item Features
- Fast and simple installation
- No torches or heat source required
- No special tools required to install splice
- Thick walls to resist puncture and abrasion damage
- High dielectric constant stress control included with 5/8 kV kits for shielded feeder cables for minimizing size and electrical stress
- Easy re-entry, can be used on cables with a rated operating temperature of 90 deg c and an emergency overload rating of 130 deg C, to splice (insulate and seal) motor lead connections for 1000 vac and less cables sized 16 AWG to 500 kcmil
- Suitable for use with 30000 series copper compression lugs or other UL listed copper lugs
- 365 V/mil dielectric strength
- 750% elongation
- 1400 psi tensile strength
- 1/2 in maximum bolt length
- Polyethylene cable
- 10 to 4 AWG feeder cable, 12 to 4 AWG motor lead conductor size
- Designed to use with copper compression, one hole lugs
- Slip-on lug cover is made of durable EPDM rubber
Specifications
- ColorBlack
- Conductor Size10 to 4 AWG
- Connector TypePigtail
- Dimensions4 in L
- Insulation Size0.17 to 0.36 in OD
- MaterialEPDM Rubber
- Number of Conductors1
- Series5300
- Splice Length3.4 in
- Temperature Rating90 to 130 deg C
- Voltage Rating0 to 1000 VAC